Results 1 – 8 of 8 Induction Generators for Wind Power by Vladislav Akhmatov and a great selection of related books, art and collectibles available now at. Induction Generators for Wind Power – Free download as PDF File .pdf) or view Author: Vladislav Akhmatov keywords: DFIG, wind power, full-rate converter. Get this from a library! Induction generators for wind power. [Vladislav Akhmatov].
|Published (Last):||19 November 2004|
|PDF File Size:||12.77 Mb|
|ePub File Size:||19.99 Mb|
|Price:||Free* [*Free Regsitration Required]|
Combined generator and turbine inertia constant H in seconds, combined viscous friction factor F in pu based on the generator rating and number of pole pairs p.
Select a Web Site
The converter C grid is used to regulate the voltage of the DC bus capacitor. The tracking characteristic is a straight line from point C and point D. When this input is high, the induction akhmatvo is disconnected from the grid and from C rotor.
Bossanyi, Wind Energy Handbook. Between point B and point C the tracking characteristic is the locus of the genfrators power of the turbine maxima of the turbine power versus turbine speed curves. Based on the following researches, while using a wind turbine which is connected with a grid following problem should arises. Over that time the turbine speed increased from 0.
The stator resistance Rs and leakage inductance Lls in pu based on the generator rating. The generic control loop is illustrated in the figure. Problem Statement 1 Develop a simulation model of wind farm. The pitch angle is kept constant at zero degrees until the speed reaches point D speed of the tracking characteristic.
Induction Generators for Wind Power – Vladislav Akhmatov – Google Books
Reactive power regulator gains [Kp Ki] This parameter is not visible when the Mode parameter is set to Voltage regulation. Direct-axis and quadrature-axis component of grid-side converter voltage in pu based on the generator rating. Default is [0 90].
The power at point D is one per unit 1 pu and the speed of the point D must be greater than the speed of point C. Simulink input of the mechanical torque.
The ppower power in VA, the nominal line-to-line voltage in Vrms and the nominal system frequency in hertz.
Click to plot the turbine power characteristics at zero degree of pitch angle for different wind speeds. This parameter is not visible when the Mode parameter is set to Var regulation. January – MarchAvailable at: Wind energy, doubly-fed induction generator- wind turbine, inruction farm, tracking characteristics.
Vladislav Akhmatov (Author of Induction Generators for Wind Power)
This paper shows that the maximum power can be extracted with the help of aerodynamic equation of wind turbine. Direct-axis and quadrature-axis component of rotor voltage in pu based on the generator rating. When External is selected, a Simulink input named Vref appears on the block, allowing you to control the reference voltage from an external signal in pu.
If the inertia and the friction factor of the turbine are implemented inside the turbine model you specify only the generator inertia constant H and the generator friction factor F.
Secondly, the graphical results were compared with the aerodynamic equation which shows the graphical model follow the maximum power tracking curve. As shown in Fig. Grid-Side Converter Control System. The following curve shown in fig. The magnetizing inductance Lm in pu based on the generator rating. The rotor side converter controls the generator in terms of active and reactive power, while the grid side converter controls the DC-link voltage and ensures operation at a large power factor.
Complete Analysis of Doubly Fed Induction Generator Wind Turbine
Default is [1 ]. Droop Xs This parameter is not visible when the Mode parameter is set to Var regulation. Gains of the var regulator.
When the wind speed drops back to a safety level, the wind turbine operation usually resumes. Grid-side coupling inductor The coupling inductance L and its resistance R in pu based on the generator rating. Generally the absolute value of slip is much lower than 1 and, consequently, P r is only a fraction of P s.
Problem Statement 4 Develop a maximum power tracking curve using the simulation result and aerodynamic equation. This parameter is used to compute the maximum current at 1 pu of voltage for C grid. The maximum power of both C grid and C rotor in pu of the nominal power. Maximum rate of change of reference grid voltage This parameter is not visible when the Mode parameter is set to Var regulation. Vref This input is visible only when the Mode of operation parameter is set to Voltage regulation and the External grid voltage reference parameter is checked.
Use this input when using an external turbine model. Direct-axis and quadrature-axis component of stator voltage in pu based on the generator rating. This external torque must be in pu based on the nominal electric power and synchronous speed.
Qref This input is visible only when the Mode of operation parameter is set to Var regulation and the External generated reactive power reference parameter is checked. Select the China site in Chinese or English for best site performance.