The regulatory requirements in maritime and offshore applications are defined by the standards IEC for maritime navigation and radio communication. Our antennas meet several international standards for marine equipment, such as IEC , GOST, IACS E10 and RMRS. Some of the tests described in the. Dedicated to safe ships and clean seas, IACS makes a unique contribution to maritime safety and regulation through technical support, compliance verification .

Author: Dagor Meztizuru
Country: Saint Kitts and Nevis
Language: English (Spanish)
Genre: Video
Published (Last): 8 October 2009
Pages: 428
PDF File Size: 15.63 Mb
ePub File Size: 9.44 Mb
ISBN: 641-5-54841-492-8
Downloads: 71532
Price: Free* [*Free Regsitration Required]
Uploader: Fektilar

Protection against cryogenic leakage and control of hazardous zones in fuel preparation iace on open deck. Equipment is to be tested in its normal position if otherwise not specified in the test specification. Mooring, Anchoring and Towing C: Salt mist test is to be carried out for equipment installed in weather exposed areas.

Electrostatic discharge IEC Contact discharge: No degradation of performance or loss of function is allowed as defined in the technical specification published by the manufacturer. The period of testing in each position should be sufficient to fully evaluate the behaviour of the e0. Using the directions defined in a to d above, the equipment is to be rolled to an angle of Pipes and Pressure Vessels S: Equipment to be mounted in consoles, housing etc.

Materials and Oacs Z: The EUT shall continue to operate as intended after the tests. Special consideration within the risk assessment of closed or semi-enclosed bunkering stations.

Strength of Ships W: The outlines of technical resolutions adopted by IACS are available at the links shown below.

  HANIF MUKHERJEE ADVANCED ACCOUNTING PDF

Selective disconnection or shutdown and equipment operable after an emergency shutdown. These inclination tests are normally not required for equipment with no moving parts.

UR E10 Rev6 CLN – IACS

Relevant tests are as listed 1e0 the Table. More severe conditions may exist for example on exhaust manifolds of diesel engines especially for medium and high speed engines.

The Equipment Under Test shall continue to operate as intended during and after the test. For equipment installed on the bridge and deck zone, the test levels shall be uacs to 10V rms for spot frequencies in accordance with IEC at 2, 3, 4, 6.

Damp heat IEC Publication test Db – measurement of insulation resistance before test; – equipment operating during the complete first cycle and switched off during second cycle except for functional test; – functional test during the first 2 hours of the first cycle at the test temperature and during the last 2 hours of the second cycle at the test temperature; – recovery at uacs atmosphere conditions; – insulation resistance measurements and performance test.

UR E10 Rev6 CLN

For severe vibration conditions such as, e. Passenger Submersible Craft SC: Critical frequency is a frequency at which the equipment being tested may exhibit: Recent revisions and changes have been underlined for easy reference.

Electrical and electronic oacs on board ships, required neither by classification rules nor by International Conventions, liable to cause eletromagnetic disturbance shall be of type which fulfill the test requirements of test specification items 19 and The test in each direction is to be carried out for not less than 15 minutes.

  COME THOU FOUNT OF EVERY BLESSING MACK WILBERG PDF

Interval between each application: No degradation of performance or loss of function is allowed as defined in relevant equipment standard and the technical specification published by the manufacturer. According to level 2 severity standard Single pulse time: Approval of consumables for welding normal and higher strength hull structural steels.

Appropriate location of premixed engines using fuel gas mixed with air before the turbocharger. Shipboard fittings and supporting hull structures associated with towing and mooring on conventional ships.

Winsonic – IACS-E10

External surface area of the tank for determining sizing of pressure relief valve paragraph 8. Sweep over a restricted frequency range between 0. However, equivalent testing procedure may be accepted by the individual Society provided that the Unified Requirements stated in the other columns are fulfilled.

Notes to Test No. During the test, degradation or loss of function or performance which is self recoverable is however allowed but no change of actual operating state or stored data is allowed.

Texts of the IACS Unified Requirements and Unified Interpretations are made available on this page for the period of one year following the date of adoption. Mobile Offshore Drilling Units E: Control and maintenance of pressure and temperature of liquefied gas fuel tanks after the activation of the safety system. Test criteria based upon application.