Download Heatline C28 manual. You have chosen to download this manual. Heatline C28, please click on the PDF link below. The boiler’s ‘Log Book’ must be completed at each Service visit. By means of a manual switch the C24/C28 can be set to operate in one of two operating modes, . Boiler Manuals for the Heatline Compact C28 appliance.
|Published (Last):||23 May 2018|
|PDF File Size:||5.75 Mb|
|ePub File Size:||20.85 Mb|
|Price:||Free* [*Free Regsitration Required]|
Remove the pump body from the hydraulic assembly by releasing the clip.
Whilst every attempt is made to ensure the accuracy of information contained on this help centre, errors can occasionally occur.
Boiler normal operation Your appliance can be set to work either on domestic hot water and heating or domestic hot water only. Ideal Domestic Boiler Spares.
Heatline Compact C28
Re-assemble the boiler in reverse order Secondary Heat Exchanger replacement 1. The CH was switched hewtline prior to this. Remove the chamber cover by releasing all the screws should be two on each side. Twitter YouTube Facebook Latest news. The water circulation is shown on the picture below. British Gas Boiler Spares.
Verify that the fl ow and return heating isolation valves are open F22 Water pressure of the installation Fill the installation. Whenever the pressure shown on the gauge is higher then 1.
No hot water and no central heating. Release the main gas connection between the gas valve supply tube and gas inlet valve, retaining the washer for use on reassembly 7. And Renault megane aren’t as good as they used to be either All f28 parts like washers, igniters etc will be replaced. Re-connect sensing tube and all the electrical leads 7.
Parts Replacement Repair and replacement parts To arrange parts replacement contact Heatline customer service specialists by explaining what is being requested, providing an error message if any appears on the LCD display. Discussion in ‘ Plumbing and Central Heating ‘ started by r1gaz10 Oct No water in the installation: When the boiler is intended for use with LPG it must not be installed in a room or internal space below ground level! Please note you need to have a HomeCare account with us.
Agile10 Oct Verify the igniter unit connections. As Kev says the diverter valve has failed. Open the isolating valves on the low and return connections. Verify the operation of the condensate pump F83 No water in heatlinf installation: Carry on browsing if you’re happy with this, or click here to manage cookies.
Boiler Manuals: Heatline Compact C28
Locate the central heating sensor — it is on left side of the combustion chamber on the outlet of the primary heat exchanger as shown on the picture below. Replace gas supply, pressure or gas valve. Fit the replacement switch in reverse order of removal 7.
Posting a message to the forum will remove the above advertisement. Login Checkout as c2 Register.
He call back with 15 mins and problem sorted it was a loose wire to this and said boiler was now back up and running. Primary pressure sensor ehatline turn off your appliance whenever the circuit pressure will fall under 0. Hot water demand c82 take heating mode whenever hot water tap is opened. Maximum temperature difference reached between return and flow heating. On all installations, after connecting the boiler to the system heatlinw initially filling with water, a proprietary inhibitor must be added to the system water to prevent corrosion.
We have a large range of plumbing and heating boiler spares in stock at DHS and if you require any assistance locating the correct part please feel free to contact our uk based call centre.
Remove the air pressure switch by pulling forward off its bracket 6.
Verify the observe the flame picture and Verify the CO setting. Remove the boiler casing following the steps below. All those are located on the rear of the control panel. Fit the new heat exchanger checking that the plate numbers are the same. Agile 28 Feb As you have already saved the maximum of 9 manuals to your online services account you need to delete one of these before you can save another one.
Heatline | Literature
Verify the pump connections. The comustion chamber should now be removed, It can be achived by unscrewing all four side screws 6. Remove the pipe clips on the pipes of heat exchanger 5. Located on the outlet pipe- the primary heatlind exchnager is monitoring the water temperature coming from an overheat thermostat.
A builtin pump is powered and hot water start to circulate around the central heating pipe system and radiators. A delay up to 45 sec may be observed- depending on a model.