FARGO Electronics DTC, DTC, DTC, DTC DTC color id printers, 10 Cleaning Cards, 10 Cleaning Pads, 10 cleaning tapes, full instructions. FARGO Electronics DTC, DTC, DTC, DTC DTC color id printers, DTC/ Dual hopper; PVC cards “); auto or manual feed. HID GLOBAL, HID, the HID logo, FARGO, and iCLASS, are .. installed and used in accordance with the instruction manual, may cause.

Author: Tum Daile
Country: Cuba
Language: English (Spanish)
Genre: Medical
Published (Last): 23 September 2013
Pages: 87
PDF File Size: 12.70 Mb
ePub File Size: 7.8 Mb
ISBN: 267-9-48728-811-3
Downloads: 29249
Price: Free* [*Free Regsitration Required]
Uploader: Moogunos

Continued on the next page. Remove the two 2 Circuit Board mounting screws located in the Hopper opening.

Be extremely careful not to let any alcohol drip inside the Printer! Select Setup Printer and Encoder Settings.

Selecting the Card Size continued See the previous procedure in this section. Page – Defining the Area to activate the Card G Adjust the Default settings as needed when using other types of cards.

If a Program Exception is displayed again, continue to step 2. However, it will work best with a standard resin black Ribbon. Faggo options allow you to control the Printer’s lamination process. The supply end of the overlaminate roll is the side containing the fresh, unused portion of the overlaminate. Printing A Test Image Note: The program must be etc515 to send down two or more separate pages to be printed within the same document.

See Printing the Self-test on page If the break occurs after the yellow panel is transferred to the card, reduce the Print EOF by manusl. To order additional materials, please contact your authorized reseller. Replacing The Main Board d Along the left edge of the circuit board, remove the two 2 mounting screws at the middle and lower section.

  JONGO PAULO BELLINATI PDF

Page – Calibrating the Card Lamination Module’s See the Replacing the Printhead Components procedure on the next page. Change all the margin settings to zero 0 and click OK.

FARGO Electronics DTC500 Series Troubleshooting Manual

See the next page. Adjusting The Ribbon Tension Trailing edge. When you remove the Printhead, you can see the circled area, as shown in the photo below. Internal Card Guide always remains parallel to the card path and that the screws loosened in Step 1 are retightened after each adjustment. Page – Selecting the Undefined Area s with the Be sure the Card Guide Rail always remains parallel to the card path and that the screws loosened in step 1 are retightened after each adjustment.

The card grid lines are spaced at. Verify that the Hopper Travel Motor is properly meshed with the gear assembly. Table of Contents Add to my manuals Farho.

FARGO Electronics DTC, DTC, DTC, DTC DTC color id printers

The image consists of sixteen 16 gray scale boxes and alignment arrows. Use this option only applies if a Magnetic Encoding module is installed in the Printer.

Repeat Steps 1 to 6 above until the Test Image is correctly positioned or Ribbon wrinkle manuao alleviated.

As an alternative to replacing maual Main Print Board, the chip U16 can be mnual. If there is not sufficient resistance, replace the U-shaped spring on the back of the Flipper Table. Comments to this Manuals Your Name. To illustrate this, the card illustration shown in the Image Position box will flip and rotate according to whether you have selected the Portrait or Landscape radio buttons.

  28C16 DATASHEET PDF

Got it, continue to print. Disconnect the cable connector.

Lift the manusl off of the Printer. When you start to print, the Lamination Drive Hubs will automatically engage the overlaminate core notches. Change the Prox Setting from None to Installed. The next card is then fed into the Printer and the next coinciding print job then printed.

Fargo DTC500 Specifications

Printer will rest securely in the holes in the lamination module’s Baseplate when the Printer is seated properly. If the test card dyc515 not look like the sample shown below, go to step 5 to adjust the Ribbon Tension. This is the fastest way to apply the film lamination, yet it provides the lowest film durability. Press the Select button to save the value. Encoding Errors Determine if the Main Board is bad.

FARGO DTC SPECIFICATIONS Pdf Download.

Measure the total area, and enter those dimensions into the Dimension boxes. This square represents the first defined area. The self-test print will begin as soon as the test image is processed. Each Firmware type has a different update process. Locate the Sensor near the manua of the Printer.