The story here is that I never watched a video for intuitive F2L because they were all too long. I find that I learn better from videos, but I’m also. F2L (First 2 Layers) is a way of continuing after solving the cross. In most cases those algorithms are simply the intuitive pair-and-insert. The name CFOP comes from the steps involved (Cross, F2L, OLL, PLL), and you . Rather than relying on a big table of algorithms, F2L is best done intuitively.
|Published (Last):||6 March 2012|
|PDF File Size:||17.27 Mb|
|ePub File Size:||8.24 Mb|
|Price:||Free* [*Free Regsitration Required]|
As mentioned above, the sections in this method don’t have to be learned sequentially. If the desired corner or edge pieces are not in the U layer, tutorjal they’ll need to be brought up before these cases can be applied. It can be quite difficult certainly so if you’ve only just started doing it upside down but tuttorial practice it will become very easy to isolate only the four edge pieces you need and formulate a basic plan to get them into a cross. Because it was taken already, that’s why. Home Old Updates Contact Me.
All of that being said, I can give you some situations to hopefully make the process easier. So instead, what we’re going to do, you and I, is cheat a little.
To build a 1x2x2 block a D-layer corner and two edge pieces are needed a D-face edge and a mid-slice edge. Even though you can already solve this case using the beginner way, I would take the time to practise and learn this algorithm now. Instead, a simple U’ before the algorithm means that when you then pair the red-blue corner and edge piece, you avoid affecting the blue-orange pair.
The only pairs that needs both R and F turns are the six ones with the edge unoriented in the slot, if the edge is oriented in the slot both ways works.
But you could also place the white-red piece by doing this:. If you had no correct edges in your last layer, you can just use one of the above algorithms anyway, like with the corners in the previous step.
The two cases are shown below:. They don’t look scary at all, and there’s even some triggers in there that you’ve already seen! Forums New posts Search forums.
Intuitive F2L Tutorial in 6 Minutes + Example | SpeedSolving Puzzles Community
Otherwise, they will only confuse you! The order of execution depends on the situation. Go on, I’ll wait right here. The second algorithm looks the picture tutoiral perfection – short and repetitive.
Being able to identify it easily will make algorithms that use it easier to learn, tktorial whenever it is used in this guide it will be tutprial in red. Going slowly isn’t better – going faster is better, but you’ll get faster by going slower. They also tend to use more double layer turns like d as opposed U y’. The algorithm page has each OLL algorithm ordered by the shape they resemble, so you can find which situation you need easily. But now you’re hooked.
The first algorithm does successfully pair the red-blue corner and edge pieces, but it also futorial out the blue-orange pair from its proper place, thereby undoing any hard work it took to put it there. If you used the second algorithm instead, then the same thing happens to red-blue corner and edge pieces, but now the red-green pieces are much happier and are in a position to be solved much more easily.
F2L Algorithms Page
World Cube Association Regulation A3a1 states tutoria, a competitor has up to 15 seconds of inspection time before attempting a solve, and you would want to be spending this time mentally formulating a complete solution to the cross which you could then execute very quickly at the start of your solve. Thread starter Smiles Start date Jul 4, There are, however, a few situations you might find yourself in where this procedure is not quite so obvious.
And I’m sure that as my F2l improves my times will drop quite a bit as I’m now spending about half my solve time 30 seconds plus just on the cross and F2L. Or you can check the advanced F2L section. If tuyorial need to swap opposite edges, you can use this algorithm:. Therefore, rotate the cube as little as possible. Instead, really try and solve each case intuitively. At tuforial stage, a lot of people still find it quite difficult to intuitively manipulate the cube.
Introduction Notation Step 1: Wiki tools Special pages. Why not see how well you can do with the timerand please fl2 get in touch if you have anything you’d like to say, or leave a comment below!
This advice applies to all of steps in this guide, but it is most important during F2L and step 1, the cross. If you can intuitively solve every F2L situation you come across then jolly well done, but there are a few cases where there is just futorial better, faster, tuotrial less obvious algorithm to solve it. This will correctly permute one of the edges, allowing you to solve the rest with one more use of the above algorithms.