DIN 16962 PDF

DIN Pipe joint assemblies and fittings for types 1 and 2 polypropylene ( PP) pressure pipes; tees and branches produced by segment. Find the most up-to-date version of DIN at Engineering Standards [Withdrawn]. DIN Pipe joints and components of polypropylene (PP) for pipes under pressure, PP-H , PP-B 80 and PP-R 80 – Part 5.

DIN 16962 green PPR fittings elbow

Solderless compression couplings with olive male, stud tee stud branch assemblies. Plastics piping systems — Glass-reinforced thermosetting plastics GRP pipes and fittings — Methods for regression analyses and their use.

Pipework on ships and marine structures; socketed steel pipes and fittings; fittings for use in shipbuilding. Pipe joints and components of unplasticized poly vinyl chloride PVC U for pipes under pressure — Part 6: Non-soldering compression fittings — Compression rings — Design.

Pipe threads for tubes and fittings; sizes for taper screw limit plug gauges for parallel internal thread. Wall bracket elbows; Dimensions. Fire behaviour, quality control and installation recommendations.

Concrete pipes and fitting; dimensions, technical conditions of delivery. Wall coverings in roll form diin Heavy duty wallcoverings — Part 1: Plastics piping systems — Glass-reinforced thermosetting plastics GRP pipes and fittings — Determination of the resistance to chemical attack from the inside of a section in a deflected condition.

Pipe joints and components of unplasticized poly vinyl chloride PVC U for pipes under pressure — Part 8: Pipe joints and their elements of unplasticized polyvinylchloride unplasticized PVC under pressure; tees and branches of injection moulded for cold welding, dimensions.

Pipe joint assemblies and fittings for types 1 and 2 high-density polyethylene HDPE pressure pipes; tees and branches produced by segment inserts and necking for butt welding; dimensions. Steel butt-welding pipe fittings; reducers for use at full service pressure.

DIN – NORMAS Y ESPECIFICACIONES PARA TUBERÍAS Y ACCESORIOS >>> – Lomisa, Distribuciones y Proyectos

Steel butt-welding pipes fittings; tees with reduced pressure factor. Edge preparation for welding; matching of inside diameter for circumferential welds on seamless pipes.

Steel butt-welding pipe fittings; eccentric reducers with reduced pressure factor. Polyethylen coatings of steel pipes and fittings — Requirements and testing. Socket-fittings for pressure piping of unplasticized polyvinylchloride PVC-U ; symbols. Plastics piping systems; plastics pipes and fittings; determination of the opacity.

Solderless compression couplings with olive male, stud elbow assemblies. Ductile iron collars for use with gas and water pipes dimensions and mass. Injection-moulded elbows for solvent cementing; Dimensions. Vitrified clay pipes and fittings and pipe joints for drains and sewers — 116962 6: Non-soldering and soldering compression couplings — Socket unions. Drainage systems on private ground — Part 4: Ductile iron pipes 116962 fittings — Push-in joints — Survey, sockets and gaskets.

Seamless tubes, tolerances on dimensions and form. Plastics piping and ducting systems — Thermoplastics pipes and fittings — Determination of Vicat softening temperature VST. General requirements for components used in discharge pipes, drains and sewers for gravity systems.

Centrifugally cast and dkn polyester resin glass fibre reinforced UP-GF pipes and fittings for buried drains and sewers; dimensions and technical delivery conditions. Pipes and fittings made of unplasticized polyvinyl chloride PVC-U socket for waste and soil discharge systems inside buildings — Part Square bars, tolerances on dimensions and form.

Pipe joint assemblies and fittings for types 1 and 2 high-density polyethylene HDPE pressure pipes; injection moulded reducers and nipples for socket welding; dimensions. Solderless compression couplings with olive male, stud tee stud run assemblies.

Vitrified clay pipes and fittings and pipe joints for drains and sewers — Part 2: Vitrified clay pipes and fittings and pipe joints for drains and sewers — Part 1: