The BC is a general-purpose NPN bipolar junction transistor commonly used in European and American electronic equipment. It is notably often the first type. 2SC Transistor Datasheet pdf, 2SC Equivalent. Parameters and Characteristics. BC Transistor Datasheet pdf, BC Equivalent. Parameters and Characteristics.
|Published (Last):||15 September 2016|
|PDF File Size:||18.75 Mb|
|ePub File Size:||19.48 Mb|
|Price:||Free* [*Free Regsitration Required]|
Electronic Projects from the Next Dimension: Commercial transistors Bipolar transistors.
This group of NPN transistors share many specifications and characteristic curves, transistot differ in voltage ratings – the BC and BC are essentially the same as the BC but selected with higher breakdown voltageswhile the BC is a low noise version, and the BC is both high-voltage and low-noise.
Interface SD Card with Arduino. Electronics Circuits and Systems.
BC Transistor Pinout, Equivalent, Working As Amplifier/Switch & Datasheet
BC is general purpose silicon, NPN, bipolar junction transistor. From Wikipedia, the free encyclopedia. The same letters are used for this purpose in several other European transistors, and is similar in principle to the “Yellow”, “Blue” and so on gain groupings in Japanese transistors, but should transistorr be confused with the “A” suffix used with some American JEDEC devices, such as the 2NA, to indicate a variety of differences or enhancements over the base type.
Retrieved 8 March Please help improve this article by adding citations to reliable sources. Virgin Galactic — Commercial Space Flight.
The BC part number is assigned by Pro Electronwhich allows many manufacturers to offer electrically and physically interchangeable trabsistor under one identification. For switching applications, transistor is biased so that it remains fully on if there is a signal at its base. In other projects Wikimedia Commons. TL — Programmable Reference Voltage.
Some manufacturers place slightly different limits on the gain groups, for example the “B” group has been quoted as in a Philips datasheet. When this transistor is fully biased, it can allow a maximum of mA to flow across the collector and emitter.
The value of I B should not exceed 5mA. Arduino based GPS receiver. The input signal at base is amplified and taken at the emitter.
Paranormal Experiments for Hobbyists. The assignment of transistor elements b,c,e to leads, i. A Transistors acts as an Amplifier when operating in Active Region.
Retrieved 28 March When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above. The transistor terminals require a fixed DC voltage to operate in the desired region of its characteristic curves.
The voltage divider is the commonly used biasing mode. Its equivalent transistors are 2N and 2SC Anything more than 5mA will kill the Transistor; hence a resistor is always added trannsistor series with base pin to limit the current. Sometimes the middle pin is supplied bent to form a triangle of leads as found in TO case transistors and, for example, the ZTXL to match the pinout of the BC more exactly.
Views Read Edit View history. It can amplify power, voltage and current at different configurations. For switching applications, transistor is biased so that it remains fully on if there is a signal at its base.
BC548 Datasheet, Equivalent, Cross Reference Search
This high-density System-in-Package SiP integrates controller, power switches, and support components. Amplifier modules like Audio amplifiers, signal Amplifier etc. The BC is supplied in a standard TO 3-pin package. This page was last edited on 17 Novemberat In the absence of base hransistor, it gets completely off. Vol 7 Number 2. What is Web Browser.
BC has a gain value of tothis value determines the amplification translstor of the transistor. Retrieved 28 June Devices registered to this Pro Electron number must have the following minimum performance characteristics: Choosing Battery for Robots. The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor.
When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region transistoe the Base Emitter voltage could be around mV.