EDSVSS−9. 9ä. System Manual. (Extension). 75 kW l. EVSxS EVSxS. Servo inverter. Global Drive. The System Manual is the basis for the description of the vector frequency inverter. Together with the System Manual (extension), document number. The vector range of frequency inverters is also perfectly equipped to handle complex applications, such as deployments in dosing, filling and feedforward.

Author: Maugis Vizragore
Country: Cape Verde
Language: English (Spanish)
Genre: Photos
Published (Last): 21 February 2012
Pages: 420
PDF File Size: 3.21 Mb
ePub File Size: 11.60 Mb
ISBN: 227-8-86352-137-3
Downloads: 49046
Price: Free* [*Free Regsitration Required]
Uploader: Jukus

9300 vector frequency inverters

Hello aran; Anything is possible, with enough ressourcesinformation and time. Error in positioning program. An absolute parameter set C was performed during relative positioning position mode C The angle difference between set and actual position is larger than the following error limit set under C Error “positive limit switch”.

Error of the program function “set position value”. Have a look at this document from Helmholtz, it gives an example on whatmust be set and how to so the CAN modules can read and write to a drive: Best regards CS Moderator.

Site Explorer Site Explorer. In the case of absolute positioning, no homing was performed before the first positioning.

Parameter set mode is absolute instead of relative. Internal fault power stage. Temperature inside the controller Sensor for detecting the internal temperature indicates undefined values.

9300 series servo inverters

Change the parameter set from absolute to relative. Temperature inside the controller. Error “actual reference dimension offset”. Hope this helps, Daniel Chartier. Find out why the value was not reached e.

  ILLEM ETIKETT PROTOKOLL PDF

servo PLC – Lenze in Denmark. As easy as that.

Find out why the value was exceeded e. Handling blocks should be ordered from Helmholtz, look on page 96 of the document page 8 of Complain wrong Brand wrong Model non readable.

Product Support Services Forum mySupport. Anything is possible, with enough ressourceslenez and time. Increase following error limit under C Actual reference dimension offset C outside the position limits.

Positive position limit C was exceeded. A parameter set with final speed must be followed by a parameter set with positioning; it is not permissible to wait for input. Error “positive position limit”. If necessary, adapt the position limit values or check whether the program function “set position value” is to be applied. New question published by Shahjee is split to a separate thread with the subject brake functions or Brakes will Automatically applied. Sensor for detecting the internal temperature indicates undefined values.

Negative limit switch was reached. Perform one of the following functions and restart:. Troubleshooting and fault elimination, System error messages general error messages — Lenze 0.

You could probably recreate the Helmhotz drivers by yourself, if you knew how the CAN module communicates with the CPU over the backplane, how the CAN module must be parametrized for CAN BUS and how toexchange betweenthe CAN module and the drive,, If you do not have the information, I strongly suggest you get purchase the Helmholts CAN parametrization software and the handling blocks for the S, so you can concentrate on your project making the drives do what you need them to do instead of finding ways to talk to the drives.

  2008 CORVETTE OWNER MANUAL PDF

Troubleshooting and fault elimination.

Error lejze position limit”. Control drive in positive direction. Error “negative limit switch”. If you do not have the information, I strongly suggest you get purchase the Helmholts CAN parametrization software and the handling blocks for the S, so you can concentrate on your project making the drives do what you need them to do instead of finding ways to talk to the drives.

servo PLC – Lenze in the Americas. As easy as that.

Drive cannot follow the digital frequency I. Have a look at this document from Helmholtz, it gives an example on whatmust be set and how to so the CAN modules can read and write to a drive:. Negative position limit C was not reached.

The reference point is not known. Kenze homing in the program.