SN QUADRUPLE 2-INPUT POSITIVE-NAND BUFFERS WITH OPEN COLLECTOR OUTPUTS Datasheet. SN QUADRUPLE 2-INPUT. Datasheets. ˇˇ. CLICK HERE for the TTL and CMOS logic listings! CLICK HERE for links to other useful datasheet sites! This page contains links to datasheets for . Rev. 7 — 25 November Product data sheet. Table 1. Ordering information. Type number Package. Temperature range Name. Description. Version.

Author: Gugis Kazigar
Country: Lesotho
Language: English (Spanish)
Genre: Sex
Published (Last): 13 July 2013
Pages: 214
PDF File Size: 15.82 Mb
ePub File Size: 17.38 Mb
ISBN: 676-8-72136-701-2
Downloads: 16282
Price: Free* [*Free Regsitration Required]
Uploader: Fenrikazahn

These parts are prefixed with 54 instead of 74 dxtasheet the part number. If you’re not using all of the pins in one bank, spread them out so it’s easier to tell which is which.

In a few instances, such as the andthe same suffix in different families do not have completely equivalent logic functions. Archived PDF from the original on July 9, By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. A series TTL device like the one you have has internal pull ups, which means when floating the pins will pull high – basically all your inputs are always high.

Use the four possible input combinations to the gate to show that it performs as expected. Surface mount parts with a single gate often 74sx a 5-pin or 6-pin package are prefixed with G instead of However, different manufacturers will use different prefixes or no prefix at all.

  BIOLOGIJA CELIJE PDF

PC/CP120 Digital Electronics Lab

June Learn how and when to remove this template message. As board designs have migrated away from large amounts of logic chips, so has the need for many of the same 774xx in one package. PLA 12 inputs, 32 terms, 6 outputs, 4 state registers. From Wikipedia, the free encyclopedia. PLA 12 inputs, 50 terms, 6 outputs.

Digital electronics Electronic design Electronics lists Integrated circuits. Here is the datashet sheet of the IC I’m not sure who manufactured the chip but it says N on it: Retrieved July 27, But without an actual photo that is a guess. You need to know where the power supply is connected and where the gate inputs and outputs are connected.

Here is a chart to sumarize the behavior of the circuit I built:. You will need to look at the IC’s datasheet. With nothing connected the input will float at about 1.

The concept is simple. See datasheet for an example. No, your input bits are never low. N This indicates the package type This will indicate which version of the pinout applies to this chip. Articles lacking in-text citations from June All articles lacking in-text citations.

Just treat the switch being closed as a 0. AND-gated positive edge triggered J-K flip-flopasynchronous preset and clear. This method has the disadvantage that when datqsheet switch is ON it puts 5V across the resistor, which wastes current.

PC/CP Digital Integrated Circuits Introduction

Older discontinued parts may be available from a limited number of sellers as new old stock NOSthough some are much harder to find.

  CALEFFI 316 PDF

This page was last edited on 27 Novemberat Parts in this section have a pin count of 14 pins or more. The pins on an N-pin DIP are numbered datasehet shown: In other projects Wikimedia Commons.

You’ll use a debugger board for input and output. When the switch is OFF it connects nothingand the input is ‘floating’. Here is a diagram of the circuit: See List of series integrated circuits. Dataasheet following is a list of series digital logic integrated circuits. Conversely, the series has “borrowed” from the series – such as the CD and CD being pin-for-pin functional replacements for 74C and 74C There are two 4 bit inputs going into the IC.

Also you are not connecting your inputs properly. Notice that this chip has fourteen pins. IC manufacturers continue to make a core subset of this group, but many of these part numbers are considered obsolete and no longer manufactured.

Due to the popularity of these parts, other manufacturers have released pin-to-pin compatible devices which kept the sequence number as an aid to identification of compatible parts.

Be sure to apply power and ground to both the chip and the debugger board.