25LC Kbit SPI Bus Serial EEPROM The Microchip Technology Inc. 25AA/25LC *? Byte and Page-level Write Operations (25XX) is a 25LCI/SN Microchip Technology EEPROM k 64Kx8 V SER EE IND datasheet, inventory & pricing. 25LCI/SN from MICROCHIP >> Specification: EEPROM, Serial SPI, Kbit, 64K x 8bit, 20 MHz, SOIC, Technical Datasheet: 25LCI/SN Datasheet.

Author: Kajikinos Nelmaran
Country: Libya
Language: English (Spanish)
Genre: Spiritual
Published (Last): 23 July 2017
Pages: 352
PDF File Size: 10.16 Mb
ePub File Size: 18.52 Mb
ISBN: 450-1-96784-802-7
Downloads: 12445
Price: Free* [*Free Regsitration Required]
Uploader: Voodoozahn

Data Sheets

Additionally, I did create a ns and microsecond delay functions I can also test as well, but I’ll try the ms delay with the system tick first. We end the setup function by sending dztasheet word “hi” plus a line feed out the built in serial port for debugging purposes.

Read operations are not concerned with page boundaries. It really helped me! Instead of a byte by byte insertion on the 25LC,since its write cycles count per page as i understand it Leave a Reply Cancel reply Your email address will not be published.

The 25LC can operate between 2. PIC32 pin 11 25LC pin 1. Store the data in ram, till you write it. From your comments i understand that the damage is caused on the individual bits actually being written If I was missing any thing, Please guide me to complete this task. When the address increments to we turn it back to 0 because we have only filled addresses in the EEPROM with data:.

  COMAG SL45 HDMI BEDIENUNGSANLEITUNG PDF

Here we allocate the global variables we will be using later in the program. It looks like they already have done the heavy lifting for me in regard to setting up the clock and power.

You are exactly right the delays actually only worked for sending and receiving 1 byte, when I recently tried multiple bytes and it doesn’t work. Here is what the read statement look like within the main while loop now: Fri Jul 20, 1: The first step is setting up our pre-processor directives.

25LC512 Datasheet PDF

It’s memory is organized as pages of bytes each. Your email address will not be published.

Display posts from previous: Control registers 2l5c512 control settings for various microcontroller functionalities. If you need larger capacity external memory, something like flash would be more suitable. It is perhaps than 225lc512 so see with your scope, and you see if speed makes a problem. A register is just a byte of microcontroller memory that can be read from or written to. Then I try to read the value from address 0: Is this correctly read?

With an SPI connection there is always one master device usually a microcontroller which controls the peripheral devices.

  ABIT KN9 ULTRA MANUAL PDF

SPI and the 25LC EEPROM | M5

If anyone can help me out it would be much appreciated. I think I can use the match register to do this I just have to configure the PCLK to be system clock divided by 2 instead of 4. The device is enabled by pulling the Chip Select CS pin low.

Last edited by treitmey on Fri Jul 20, The device also offers various degerees of write protection and a hold pin, but fatasheet won’t be covering those in this tutorial. This function could easily be changed to fill the array with data relevant to your application:.

All times are GMT – 6 Hours. I think that would be more convinient. Very helpful with SPI! Note char buffer []. Hello Nick, you can lower clk from 10 MHz to e. Instructions are sent as 8 bit operational codes opcodes and are shifted in on the rising ratasheet of the data clock.

I’m not sure what else is required. Can you show what configuration parameter you are using?