LMN Datasheet, LMN National Semiconductor Voltage Comparator Datasheet, buy LMN. The LM, LM, LM are voltage comparators that have low input currents. They are also designed to operate over a wide range of. Part, LMN. Category. Description, Voltage Comparators. Company, ST Microelectronics, Inc. Datasheet, Download LMN datasheet. Cross ref.

Author: Zulull Faem
Country: Pakistan
Language: English (Spanish)
Genre: Spiritual
Published (Last): 25 July 2018
Pages: 399
PDF File Size: 14.23 Mb
ePub File Size: 1.57 Mb
ISBN: 535-5-20655-128-9
Downloads: 25550
Price: Free* [*Free Regsitration Required]
Uploader: Bakree

Any Op-Amp can be made to work as a voltage comparator, but the LM proves itself to be advantages by housing an Output Transistor inside its package.

Message 4 of 5. As grounding unused pins is a practice on electronics, Dataseet guess it was the way of the designer to make sure the device was not disabled for a ground wired to that pin. The LM can work on a Single supply voltage or in a dual supply mode. Could the component model be the issue? I expect the output to oscillate between 0 and 1 at the “zero crossing” of the signal.

LM Pinout, Pin Configuration, Specifications, Equivalent, Working & Datasheet

Message 3 of 5. The transistor can also lm131n the Load to be isolated from the system ground, so if you are looking for a Voltage comparator to drive loads of these specifications then this IC might be the right choice for you. Any help is appreciated. Why is it not working in Multisim?

  ANAESTHESIA VAPORIZERS PDF

Multisim and Ultiboard

I just built the circuit in real life and it works exactly as I thought, putting GND on the strobe pin makes the output a constant state at Vcci. I tried adding in a transistor with a 1k resistor to ground and a TTL signal at the base as per the datasheet and this doesn’t disable the output either.

When not in use the pins 5 and 6 should be shorted as shown above. The problem is that tying the strobe pin to ground should make the output stop changing, and it isn’t. You can refer the other possible circuits from the LM datasheet given at bottom. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.

I built a simple circuit datsheet the LMN comparator.

LMN Comparator with Strobe – Discussion Forums – National Instruments

The simplified schematics of the IC is shown below:. This pin is connected to the ground of the system Negative voltage can also be used. The output is correct as seen on the scope. TL — Programmable Reference Voltage. You can note that the Output voltage stays high when pin 2 has higher voltage than pin 7 and vice versa.

Submitted by admin on 6 March Attached is a Multisim file with every comparator with a strobe feature available in Multisim and a picture of the circuit. Message 5 of 5. The simplified schematics of the IC is shown below: The pins 5 and 6 on the Op-amp are used to set the balance voltage if you want to manually adjust the DC-Offset voltage.

  EGON BRUNSWIK PDF

All of those comparator outputs should be a high state which means the LED will turn on connected through the 1K resistor to Vcc. Normally these pins are not used since the Input Offset itself is much better controlled.

Message 2 of 5. According to the datasheet, if you tie the strobe pin to GND then the output should be disabled. If the voltage at the Datasgeet Terminal pin 2 is higher than the Inverting Terminal pin 2the output pin 7 will also be high else the output will be low. The problem is that the strobe pin is not working for the model. A sample circuit is shown below in which the Inverting Terminal is set to 2.

LMN Comparator with Strobe. An Emitter Output Circuit is shown below. Most Active Software Boards: Message 1 of 5.