I would like to get a very nice trigger job on a SS GP for the single Ruger forum I found the IBOK for the GP on Google (GP IBOK). I received the GP pdf this morning. I found the IBOK so helpful thought I should bump it back up so others could keep seeing it. Gp Ibok – PDF Free. Download – -. Ruger sp manual pdf ruger sp manual pdf magnum revolver like the. Ruger GP For many.

Author: Virg Doujin
Country: Croatia
Language: English (Spanish)
Genre: Education
Published (Last): 18 July 2004
Pages: 252
PDF File Size: 13.96 Mb
ePub File Size: 3.58 Mb
ISBN: 249-4-74377-981-2
Downloads: 24110
Price: Free* [*Free Regsitration Required]
Uploader: Kazralar

Fixed sight models are available in 3 and 4 inch barrels. Also, remove any machine marks from the bottom surface and buff it smooth. The only other parts that are unique to a certain model are the cylinders when chambered for a 38 Special or Magnum or hammers in DAO models bobbed.

Use a paper clip or stiff wire and push the latch retaining pin part 20 completely out.

Use the windage screw to center the sight blade by turning the screw clockwise. The design is a modular concept with three main assemblies.

Any rough spot will cause the pawl to dig in, make DA trigger pull raspy, and will wear the tip of the pawl. To remove the grips, unscrew the grip screw part 19 most of the way out then push on the head of the screw to dislodge the left grip panel part This is a very usefull information! With your right hand, pull the pawl to the right to remove.

Sometimes it’s frustrating reloading for semiautos because you have to make small batches of rounds and test them for reliability with each gun if you change anything about the load. I just purchased a Used Gp made in This makes trigger guard removal very difficult.

  DIRK TREUSCH SEMINARHEFT PDF

The latch should drop then pop back up and drag on the cylinder. If headspace is too tight, the case heads may drag on the recoil shield and hamper cylinder movement.

Find all posts by Hungry. It will ibkk you thru a trigger job and general fine tuning. This is evidenced by measuring the SA trigger pull 10 times and getting different pull weights.

• View topic – IBOK for GP

You are commenting using your WordPress. Typically, the tips have a line of galling on the top outer edge. The guns felt like they had trigger jobs done on them. Iowegan, I’ve also sent you an email requesting the. Actually it is the only handgun I own. It’s very accurate as well. You may find a used one from Numrich or E-bay. Place endshake bearing s on the crane tube and insert the crane into the cylinder. Iok the screw clockwise will move the sight blade to the left and will move the point of impact to the left as well.

As you said though. Cocking the hammer for single action takes barely any effort compared to before and is super smooth.

Test the ejector rod by pushing it in and allowing it to spring back. If initial timing is slow, the cylinder will try to rotate ggp100 it is released. Bottom line is that Ruger makes good revolvers that are build to last and work well out of the box. To remove the hammer strut assembly, cock the hammer then place the disassembly pin part 9 in the hole near the end of the hammer strut part Advanced Action Work There are a number of things you can do with a GP that require machining gp1000 skills beyond a hobbyist.

I put the Hi-viz front sight on it and the new grips came in.

New GP – Survivalist Forum

I’m very pleased with the improvements to the GP and it just became one of my favorites. Yes, please do, I would love to see inok. Use a small punch or screwdriver and push in on the front sight plunger part Big Andy This space for rent. If it is rough, you will feel a gag in the DA stroke. You can open the throats to.

  JVC HM100 MANUAL PDF

gp1100 Hammer reaches the cocking point and is held to the rear by the SA sear. With the gun fully assembled, measure the gap between one side of the hammer and gp10 frame.

The tip of the plunger snaps into a hole in the frame, just behind the trigger guard and inside the grip frame. Insert the latch pivot pin part Insert the grip screw from the right side and tighten it with a screwdriver.

Stainless steel is also pretty forgiving. In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic. The center pin rod is pushed forward and releases from the frame hole. You have no idea how great that makes me feel that you think so highly of my blog.

But then of course gunsmiths would have less income from fixing Ibko revolvers!

GP100 IBOK for SP101

Not too many parts. I’ve been shooting 9mm gp1100. Amazon is offering free shippping, so factor that into the price and I think it’s a pretty good deal.

All the options you have as far as making and shooting different loads and powder charges without having to think about a malfunction is what makes me like them so much.