WCDMA RAN Systems and Site Introduction. RBS components. WCDMA RBS Maintenance. 2. Customer Product Information (CPI) and. TXO Systems has the ERICSSON RBS RRUS 12 B3 in stock, along with a wide range of used and refurbished telecommunications equipment from all. Ericsson shall have no liability for any error or damage of any kind resulting from The support system for the RBS main unit is available in two variants.
|Published (Last):||15 April 2012|
|PDF File Size:||11.79 Mb|
|ePub File Size:||9.76 Mb|
|Price:||Free* [*Free Regsitration Required]|
Exhaust air from the rear may not be allowed to circulate to the front air intake in the eficsson. Check that the items delivered correspond to the packing list. Detailed information is found in Hardware Maintenance Instructions.
BTS FOR ERICSSON RBS – BFL /1 R3A – DUW 20 01 – KDU /2 R3B | eBay
Sell now – Have one to ericswon Connect the alarm signal wires to the alarm connector by inserting each wire into each dedicated tension clamp connection and check that they are properly fastened.
Select one of the following three options for connecting the on-site transmission system and go to the appropriate section: To connect the RBS to the twisted-pair cable: Make sure that cables with recommended cross sectional area are used.
Align the lock of the cable protective cab and close it as shown in numbers 3 and 4 in the following figure.
Ericsson RBS LTE Indoor Main Unit Remote Base Station 1/bfl /4 | eBay
Therefore, install the main unit reicsson a convenient working height and route all cables with necessary extra length to allow the removal of the main unit without disconnecting the cables. Use the checklist in Table 6 to recycle and sort waste. Fill in the verification checklist in Site Installation Documentation.
No additional import charges at delivery! Seller does not offer returns. Figure 3 shows the grounding for the support system variant 1, and Figure 4 for the support system variant 2.
Make erisson that the cable connectors and the connectors on the XMU are clean.
Do not tighten the cable straps too tight. Leave the protective cap on the inactive fiber marked with yellow. To prepare for an expansion with a secondary support system, reserve space close to this main unit. To remove a wire from the connector, push the corresponding release tab on the connector with a small screwdriver and carefully pull the wire. Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab Add to watch list.
Mouse over to Zoom – Click to enlarge.
Detailed information can be found in Site Installation Documentation. Strip off 12 mm of each wire using the cable shield cutter.
ericsson rbs 6601
Make sure that the external alarm cable from the SAU has enough extra length to allow the removal of the main unit from the rack for service purposes without disconnecting the cable. Trademark List All trademarks mentioned herein are the property of their respective owners.
Hand over Site Installation Documentation to the person responsible for the site. Information about transmission alternatives and the connections to be used for erivsson site can be found in Site Installation Documentation. The TCU is installed in the slot 2 in the main unit. Contact the seller – opens in a new window or tab and request a shipping method to your location. Some red indicators may flicker during startup.
You are free to manage this via your browser settings at any time. Detailed information about optical indicators can be found in Indicators, Buttons, and Switches.
The front cover is only applicable with the support system variant 2. Subject to credit approval. See terms – opens in a new window or tab. More information can be found in Site Installation Documentation.
Enter the email address you signed up with and we’ll email you a reset link. Never touch the end-face of the optical connectors. Clean the site and remove objects such as wrapping paper and cable clippings.
To remove the alarm connector, grip and pull the connector from the socket. This amount is subject to change until you make payment.
Never look directly into the end of an optical cable, or other laser source. Make sure that the DC power supply cable has enough extra length to allow the removal of the main unit from the rack for service purposes without disconnecting the cable.
Take care not to damage the front when handling the main unit.
If the distance is less than 50 mm, the brackets must be adjusted, see Step 2. See all electronauts has no other items for sale. Log In Sign Up. The maximum main unit weight is 10 kg.