HANDLING THIS SERVICE MANUAL About This Service Manual n. Scope This Service Manual applies to the Fuji Medical Dry Laser Imager DRYPIX Service Technicians PACS / DR / CR / Digital Forum Drypix Service Manual CARLOS RUEDA Innovacion Tecnologica Hello, I am trying. View and Download FujiFilm DRYPIX service manual online. DRYPIX Printer pdf manual download.

Author: Vudohn Tusida
Country: Sri Lanka
Language: English (Spanish)
Genre: History
Published (Last): 4 April 2004
Pages: 197
PDF File Size: 8.68 Mb
ePub File Size: 7.52 Mb
ISBN: 122-9-87870-937-6
Downloads: 15795
Price: Free* [*Free Regsitration Required]
Uploader: Akinogami

Not only does each mammographic x-ray Page 91 Rotate the positioning screw in the clockwise or counterclockwise mnual and adjust. Place the tip in front and behind the right rail of the tray loading unit on the aperture of the tray loading unit, tighten the rail temporarily with the screws.

Install the inside belt first and then the top and bottom belts. Push down the plate, and with an approximately 50 mm space between the plate and stopper, push the suction cup against the film. Display in Community Feed.

When removing the squeezing roller, be careful not to damage the bearing of the tray, Remove drgpix squeezing roller. MC Remove the film release unit.

FujiFilm DRYPIX 7000 Service Manual

MC Reinstalling Procedure Insert the sub-scanning unit into the equipment, and temporarily secure with the screws. Dear sir, I am a service engineer free lance. Forums Mannual Parts Videos News. EPS Remove the upper conveyor unit removing jig. Page 87 Remove the sub-scanning unit fixing bracket, and reinstall it to its original position.

  BEZONKEN ROOD PDF

Reinstalling Procedure There are three timing belts. Don’t show me this message again. By continuing to browse the site you are agreeing to our use of cookies.

Documents Flashcards Grammar checker. Steps that differ between the three seevice are indicated separately. Removal Drive Cam Remove the gear 1 and gear 2. Don’t have an account?

MC Remove the tray. Geometry Recording Length and Width 4. Remove the PC board. The DryPix is a dry laser imager which combines the high quality and performance of Fuji’s centralized imagers, with an extremely compact design and convenient volt power, required for decentralized imaging applications.

Artifacts Output test pattern films to make sure that there are no clinically significant artifacts, such as banding, scratch, fog etc. If the equipment mounts film tray 2, loosen the screws securing the idle gear of the middle conveyor unit. Output the grid pattern using the M-Utility. Reinstall in the reverse order of removal. Rail of equipment FP7C Page 58 Secure the gear while pressing the flange of the idle gear against the gears in the arrow direction shown below. Two minutes later, check that the space is still 50 mm.

  EL GALLO DE ARTURO USLAR PIETRI PDF

MC Reinstall the sub-scanning unit fixing bracket at the position shown below. Remove the sub-scanning unit fixing bracket, and reinstall it to its original position. Remove the sub-scanning unit fixing bracket. Remove the lower conveyor unit. The screws painted in yellow must be adjusted after the installation of parts. Artifacts Banding, Scratch, Fog, etc.

FUJIFILM DRYPIX SERVICE MANUAL Pdf Download.

Inner slide rail FP7C Film Positioning Assembly lower Remove the grip position detection sensor bracket. Remove the gear 1 and gear 2. Shutdown the PC for servicing. Add to My Bench.

Page 16 MC Remove the tray inside cover. When installing parts, this is indicated if alignment to the boss is required. Page When reinstalling the adiabatic 0400, do not sandwich the thermistor cable.

Drypix 4000 service manual

Page 20 MC Remove the tray. Page 71 Open the left segvice right positioning guides until they touch the sides when installing the film positioning motor MD5. Page Rail of equipment FP7C Remove the heat development unit. Remove the connector bracket. Prepare the PC for servicing. Remove the cooling fan assembly.