Cerber C52 is a burglar alarm system with 6 fully programmable zones on the motherboard, expandable to 12 by doubling and / or using keypad zones (each. Cerber c Users Guide – Download as PDF File .pdf), Text File .txt) or read online. Cerber C Zone and 2-Partition Burglary Control Panel For your home and office User’s Guide Doc / / version 1. INTRODUCTION.

Author: Grokasa Dagor
Country: Mongolia
Language: English (Spanish)
Genre: Science
Published (Last): 17 February 2017
Pages: 292
PDF File Size: 15.9 Mb
ePub File Size: 6.60 Mb
ISBN: 145-8-26576-207-7
Downloads: 7180
Price: Free* [*Free Regsitration Required]
Uploader: Doumi

This means that user was under duress ambush. This procedure can be performed also by pressing the [BYPS] key. These events occur by activating the correspondingly 24h defined zones, or by simultaneously pressing a combination of keys from keypad: The most frequent cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance.

In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson.

Cerber C – Roel Design

LED interpretation, in case of pressing a key from 1 to 9, is accordingly performed: Please note the backup battery is continuously charged while AC power is present and if this trouble persists for a long time that cerrber the battery must be replaced. On LCD keypads you can see after arming in this mode one text similar to: The keypad will confirm entering this mode with 3 beeps.

Programming of the system time and date can be canceled by [ ] key pressing. If in this section, one of the 2 groups of 2 digits are set both with value 0, then the corresponding partition will try to auto arm after every second if no activity will be detected in the area. A ZNot k6 BypassZ part. Smoke detectors may not sense fires that start where smoke cannot reach the detectors, such as chimneys, in walls, or cerbee, or on the other side of closed doors.

  EDWARD GOREY THE GASHLYCRUMB TINIES PDF

Quick Arming Modes Arming without cegber codes Quick arming features allow the system to be quickly armed by any person who may not own a user code. After [ ] key was pressed, the keypad buzzer will sound 6 confirmation beeps and exit this section waiting for a new command to enter another section or [ ] key to exit the main programming menu.

Once the command was cefber, the master user should enter each allowed section by pressing the corresponding 2 digits i. The panel will come back in the stand-by state, waiting for commands.

In order to choose one of the options, just press the corresponding key i. Thus, the dispatcher will be informed that the user action was performed under threat.

Cerber c612 Users Guide

If the buzzer warnings were enabled by programming, during the exit delay the keypad buzzer will sound warning beeps. For system parameter cefber to be accomplished only by authorized people, this code must be changed after the system was installed! This alarm system should be tested weekly to make sure that all sensors work properly. An overload on the siren control wire is detected only during when a condition has occurred which 21 would activate the bell output e.

The keypad buzzer will sound 3 beeps after each 3-digit group and 6 beeps after the last one. Choose partition 1,2, The options displayed on the 2nd line state for choosing partition A 1partition B 2 or cancel command. In order to enter zone bypassing menu, the user should enter one of the commands: In this case, if the cerbre wants to arm the system after the siren sound was stopped, he must key in again the user code.

The following sequence will be performed: While PC modem is calling the control panel, just entering this command will manually activate the communication between PC and panel. Keypad types The next keypad models are available: Section [] — Manually Activation of PC callback The 1 to 5 options will be displayed according to the table bellow: This trouble indicator will appear if wiring between the siren and the control panel is shorted, cut-off or there is an overload on the siren control wire a 3K3 resistor must be connected across the bell terminals.

  BSI-TL 03420 PDF

After opening the short-cut or reducing the load, the bell current is restored automatically. Press [ ] key to exit system trouble displaying menu. How does a partitioned system work? System Trouble Status Displaying: To cancel the command user can press [ ] key.

In a partitioned system entering a user code with the right of siren stopping, while siren is sounding, the following conditions will apply: If the buzzer warnings were enabled by programming, then during the exit delay the keypad buzzer will sound warning beeps.

System Troublesand when enetring the menu: The following operations can be performed: The system will not generate the alarm until the entry time elapses, giving the user enough time to enter the premises and disarm the entire system or a part of it to modify the entry delay times, see section []. The list of messages that can be seen on the LCD keypads display is much longer, but easy to understand.

Cerber c Users Guide – Documents

Devices powered solely by AC will not work if their AC power supply is cut-off for any reason, even for a short period of time. A second floor detector, for example, may not sense a first floor or basement fire.

The user code must have the right for arming.