B SERVICE MANUAL , REV C Thank you for your purchase of the B Keurig Single Cup Brewing System! U U The B is the. the Cleaning Instructions in this guide. Turn off and unplug the brewer before cleaning or maintenance. Allow to cool before putting on or taking off parts. Download KEURIG B SM service manual & repair info for electronics experts.
|Published (Last):||25 November 2007|
|PDF File Size:||9.13 Mb|
|ePub File Size:||14.75 Mb|
|Price:||Free* [*Free Regsitration Required]|
This design facilitates ease of repair at customer locations. A choice of 4, 6, 8, and 10 oz cup sizes areavailable.
Keurig B User Manual – Page 1 of 92 |
Disconnect the larger hose on the right. Posted on Oct 21, Be the first to answer. B Brewer Water Flow MechanismsA schematic and legend showing the major components of the B are provided refer to page 8 and9.
After heating has taken place the display will read: The next screen will look like this hot water dispense. Fasten the brewer-cabinet plate to the cabinet three screws and to the brewer two screws. Disconnect the hoses on kejrig top of each of the water pumps.
Procedure for Setting the Brewer to Coin Operation: Looking at the right side of the brewer, take note of the cutout in the chassis near the top.
Completely loosen the two captive screws holding the Power Module to the bottom base plate and pull out slightly.
Disconnect the small tube at the union connection. This unit has two power supply cords. Removal of Back and Side Panels b. Completely loosen the two captive screws holding the Power Module to the bottom base plateand pull out slightly. Answer questions, earn points and help others Answer questions. Install the replacement sensor, the main PCB,and plastic bar. The water temperature can be set between to degrees F.
KEURIG B USE & CARE MANUAL Pdf Download.
This connection is in the upper left corner of the main PCB area. It consists of a dual water tank capacity system which allows for fast sequential brewing. The display will look like this was brewer drained: The power may be cycled to attempt to clear theerror, but if it occurs again, the same message will be displayed. The step by step procedure for installing the coin changer is as follows: The only one heater at a time is allowed to energize and the heater in the top tank brew tank has priority.
Keurig B3000 User Manual
Plug-in each units cords to outlets. Install the new module and connect all of the appropriate connections, hoses, and wires making sure that they are secure and tight.
De-scaling your brewer helps maintain the heating element and other internal parts of the mwnual that come in contact with water.
Dispose of the used K-Cups and reinstall the bin. Never immerse the base unit in water or other liquids. Municipal water is introduced to the unitthrough the inlet valve [X]. There is no pour over filling capability. keurrig
What’s missing? Tell us about it.
Attach the Puncture Mechanism Module cover and tighten itsretaining screws. Coin retrieval opening Figure 11 Figure 13 Figure 12 2. Enter your mxnual number here.
Cold Water Tank — located at the upper right rear of brewer: To remove the Front Door It will take approximately 3 mamual to complete. The MENU lists the following items. The display will look like the image on the right below. Details for the installation of the changer are provided as an appendixof this manual.
Disconnect the Multi Connector Tee manifold from During the brewing process water is introduced into the K-Cup under pressure via the entrance needle, located in the Puncture Mechanism Module. The B is also a highly serviceable brewer. The ModulesWhat follows are images of the b300 modules to show their general configuration.
Risk of electric shock.
Some states or Provinces do not allow the exclusion or limitations of incidental or consequential damages, so the above limitation or exclusion may not apply to you depending on the state or Province of purchase. All repairs of the brewing system are done on a modular level.
Risk of Fire or Electric Shock. Details for the installation of the changer are provided as an appendix of this manual. Looking at the left side of the brewer when facing from the front, locate the main power harness, andtransformer. Locate the two screws at the top of the module. The wires must be reconnected to their proper connections when installing the new module.
The items included in the accessory kit are: