ASTM Fa. Standard Specification for Wrought 18ChromiumNickel Molybdenum Stainless Steel Bar and Wire for Surgical Implants. Find the most up-to-date version of ASTM F at Engineering Mechanical values listed above are typical for uniaxial tension. Upon request, we can also deliver this material with other properties. L (ASTM F), Ti.

Author: Yozshurg Sakora
Country: Swaziland
Language: English (Spanish)
Genre: Automotive
Published (Last): 2 November 2004
Pages: 60
PDF File Size: 20.39 Mb
ePub File Size: 16.43 Mb
ISBN: 678-6-42667-354-7
Downloads: 56944
Price: Free* [*Free Regsitration Required]
Uploader: Kazilkis

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

Billet shall also be ultrasonically tested prior to being hot rolled and should be free of internal defects. Link to Active This link will always route to the current Active version of the standard.

316LS / 316LVM Surgical Stainless Steel Bar – ASTM F138

Published information has shown no adverse effect for compositions containing up to 1. While most manufacturers quickly turn to material costs as a primary means of lowering their price, these short-term accommodations are not always sustainable. A number in parentheses indicates the year v138 last reapproval.

Under minimum limit not applicable for elements where only a minimum percentage is indicated.

Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. BrinellB Hardness, max, HB Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

  EL PANOPTICO JEREMY BENTHAM PDF

Types of finish available for bar and wire products are cold-drawn, pickled, ground, and ground and polished. The technical data provided is for information only and not for design purposes.

ASTM F植入不锈钢棒材和线材_百度文库

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

Quality Program Requirements C Typically supplied as hot-rolled bar for forging applications. Last previous edition approved in as F — The secondary premium melting step imparts improved cleanliness.

Different tests shall be performed in order to determine the following mechanical properties of qstm wire and bar: Originally approved in Acceptance criteria shall be agreed to between pruchaser and supplier. Approved June 10, The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. The alloy is nonmagnetic even after severe cold forming operations.

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such asm, are entirely their own responsibility. Historical Version s – view previous versions of standard.

Hardness determination on cold-worked material shall be made on a product cross-section, midway between the center and surface, if cross-section size is adequate. F Specification for Wrought 18ChromiumNickel If you feel that your comments have not received a fair hearing you should atsm your views known to the ASTM Committee on Standards, at the address shown below.

LVM ASTM F – BME Encyclopedia

This abstract is a brief summary of the referenced standard. Aatm heat analysis shall conform to the requirements as to chemical composition specified and the material shall contain no delta ferrite, chi, or sigma phases when it is examined by metallography. C Cold-drawn wire may be ordered to tensile strengths up to psi MPa with lower elongation as determined by customer and supplier.

  DESFIBRILADOR EXTERNO AUTOMATICO PDF

Fine wire shall be furnished, as specified, in the cold-drawn condition. ff138

Analysis for elements not listed in Table 3 is not required to certify compliance with this speci? Current edition approved June 10, Advanced ladle metallurgy allows for fine adjustments of the composition, amount, size, shape and distribution of the nonmetallic inclusions normally occurring within standard stainless steel. It is not warranted or guaranteed. On the other hand, types of finish available for fine wire products are cold-drawn, ground, and ground and polished.

Bar and wire shall be furnished, as specified, in the hot-worked, annealed, cold -worked, or extra hard condition.

Combining values from the two systems may result in non-conformance with the standard. The chemistry modifications are designed to adtm the corrosion resistance of this alloy and provide a ferrite free microstructure.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.